Automotive Cerakote
Cerakote for the parts that take the heat.
Headers, valve covers, calipers, wheels, trim, and the off-road and moto parts that live in the weather — blasted, coated, and cured on the same benches that finish our firearms in Roswell. Ceramic-based, about a thousandth of an inch thick, and built for heat, chemicals, and road salt. Send us photos and a parts list for a free quote before you pull a bolt.
What we coat
Parts off cars, trucks, Jeeps and bikes
Exhaust & headers
Headers, manifolds, downpipes, turbo housings, and tips in Cerakote's high-temperature coatings, rated up to 1,800°F. Each coating series has its own heat ceiling, and color choice narrows as the temperature climbs — we'll tell you which colors hold at your part's heat.
Engine bay & intake
Valve covers, intake manifolds, timing and engine covers, brackets, pulleys, and fuel rails. A thin film that holds up to oil, fuel, coolant, and brake fluid, in nearly any color — and fasteners and gasket faces stay masked.
Brake calipers
Calipers coated in a heat- and fluid-resistant finish. They need to arrive fully stripped — pistons, seals, bleeders, and pads out. We blast and coat — no rebuilds — and bores and threads are masked so they go back together cleanly.
Wheels
Aluminum and steel wheels up to 20 inches, refinished in a single color or with a contrasting lip or face. Tires, valve stems, and weights need to come off first. We'll talk through how the finish handles tire changes and trail use before we coat.
Trim, emblems & grilles
Emblems, badges, grilles, window and door trim, mirror caps, and interior pieces — metal and many plastics, using an air-cure coating on anything that can't take the oven. A clean way to black out chrome or match a body color.
Truck, Jeep & off-road
Bumpers, rock sliders, skid plates, hinges, roof racks, and winch housings — the hardware that sees mud, salt, and rock rash. Cerakote's corrosion resistance is what it was built for, and a thinner film than powder coat keeps hinges and threaded parts fitting.
Motorcycle & powersports
Exhaust pipes, engine and clutch covers, foot pegs, levers, triple clamps, and brackets for street bikes, dirt bikes, ATVs, and side-by-sides.
Why Cerakote instead of powder coat
Powder coat is a good finish, applied thick. Cerakote goes on at around one mil — a thousandth of an inch — so it doesn't fill threads, swallow fine detail, or upset the fit of parts that bolt together tightly. It's ceramic-based, which is why it stands up to heat that would yellow or burn off most coatings, and to the brake fluid, fuel, and road salt that eat through paint.
It also comes in a far wider range of colors than you'd expect from a high-temp coating, and we mix to a target when the chart doesn't have it. That said, it's not the answer to everything, and if powder coat or paint is the better finish for your part, we'll say so.
Prep is the whole job — on a car part too
A finish is only as good as what's under it, and automotive parts arrive with more under them than firearms do: baked-on oil, old paint or powder, rust, and casting porosity that holds contaminants. We strip, degrease, media-blast to a coating profile, and bake to drive out what the metal has soaked up, so nothing gasses out under the coating and leaves pinholes.
Then we mask what has to stay bare — gasket and sealing faces, threads, bores, bearing seats — coat, and cure. Most coatings are oven-cured; air-cure coatings go on plastics and anything else that can't take the bake.
What we do and don't take on
We blast and coat parts — no maintenance, no assembly, and no removal or installation. Parts need to come to us off the vehicle, and calipers, wheels, and anything with seals or bearings should arrive stripped. If yours aren't, say so on the form and we'll tell you what has to come out before we can quote.
Drop them off at the shop in Roswell or ship them in. Either way, please wait for the quote before you send anything — we'll tell you how to pack and label the parts so they come back to the right person.
How an automotive job runs here
Free quote from photos
Send the parts list and photos through the form below. We reply with a free quote, or with the questions we need answered to give one.
Strip, degrease & blast
Old coatings, oil, and rust come off; the surface is blasted to a coating profile and baked to outgas what the metal has absorbed.
Mask, coat & cure
Sealing faces, threads, and bores are masked by hand. The coating is sprayed to an even film and cured — oven or air, to suit the part and the coating.
Inspect, photograph & return
Every part is inspected and photographed, then packed for pickup at the counter or shipped back to you.
Automotive quote
Get a free quote on your parts
Five short steps. Photos make for a faster, firmer quote — one shot of everything, plus close-ups of any rust or old coating. Please wait for the quote before you drop off or ship anything.
Answers
Automotive Cerakote questions
How much heat can it take?
It depends on the coating. We stock several Cerakote series, each with its own heat ceiling — the standard H-Series for engine-bay and trim parts, and high-temperature coatings rated up to 1,800°F for headers and exhaust. One caveat worth knowing up front: the color is rated lower than the coating — on the high-temp blacks, the manufacturer's published color stability is 1,300°F. Tell us where the part lives and we'll pick the coating to match.
Is Cerakote better than powder coat?
Different, not universally better. Cerakote is much thinner, so it keeps threads and close fits intact and holds fine detail; it handles exhaust heat that most powder coats can't; and it resists fuel, brake fluid, and salt. Powder coat is thicker and can be the right call for big, simple parts like frames. We'll recommend what suits the part.
What does it cost?
The quote is free. Automotive work is quoted per job, because a single emblem and a set of headers with a heat-sensitive color aren't the same job. What moves the price is the part count and size, what has to be stripped off first, the number of colors, and how much masking the part needs. Send photos through the form and we'll quote the whole job, at no charge, before anything starts.
Do the parts need to be off the vehicle?
Yes. We blast and coat — no maintenance, assembly, removal, or installation. Calipers should arrive with pistons, seals, and bleeders out; wheels with tires, valve stems, and weights off; and anything with bearings or rubber should be stripped. If you're not sure what needs to come out, ask on the form before you start wrenching.
Can you coat over powder coat, chrome, or old paint?
We strip it first. Coating over an old finish puts the new one's adhesion at the mercy of the old one's, and that's how a coating flakes. Stripping and blasting is part of the prep we quote.
Can you match a body color?
Often, yes. Send the paint code and a photo, or bring a painted part. We mix Cerakote to a target and can adjust the sheen, but metallic and pearl paints don't always translate to a coating, and we'll tell you honestly before we start.
Do you take parts that aren't automotive?
Yes — tools, hardware, home and commercial parts, and of course firearms. If it's metal, and many plastics, ask. For firearms, start from our Cerakote page instead; that work runs through the gunsmith bench.