Restoration
Refinishing: Cerakote, DuraCoat & Touch-Ups
The restoration side of coating: a rattle-can job stripped back to bare metal and redone right, a worn or failed finish re-coated, a pistol frame Cerakoted to match its original black polish, a scratched slide touched up, a silencer put "back to black." Cerakote and DuraCoat, prepped, applied, and cured on our own benches. New-color work, patterns, and the full chart live on the Cerakote page under Finishing.
Strip it and do it right
A lot of refinishing starts with undoing someone else's. Spray paint over a Glock, a peeling DIY coat, a Cerakote job done without the blast or the cure — it comes off completely, down to clean metal, before anything new goes on. Then the prep that makes a coating last: degreasing, blasting to a uniform profile, degassing, and a cure at the right temperature for the right time. Skip any of those and the finish fails in a year; that's the difference between a refinish that lasts and the one you're replacing.
The finish goes on in whatever the gun should wear. Sometimes that's a color — Cerakote in Lemcoe FDE, Midnight Bronze on a can, a four-color stencil camo; sometimes it's matching the original, like a CZ 82 coated to look like the polished black it shipped in. DuraCoat is the other half of the bench, and on restorations it's often the better half: the shop runs the full DuraCoat line — the colors, DuraBlue for a blued look, DuraPark for a parkerized one, DuraBrown for a browned muzzleloader, DuraFil for pitting, DuraHeat for parts that get hot — so an old gun can be refinished in something that looks like what it wore rather than a modern color. Ask and we'll say which one your gun wants.
Touch-ups, sand-downs, and back to black
Not every refinish is a whole gun. A holster-worn slide or a scratched handguard can be touched up in the matching color; a Cerakote job you've stopped liking can be sanded down and redone; a silencer that came in coated gets put back to plain black; mag bases, small parts, and controls get done to match a bigger job. Rustic and battleworn finishes — a Henry with a Cerakoted barrel and lever, parkerized tube, and polished brass; a shotgun finished to look like an old watch — are their own kind of restoration, and we do those too.
How a refinish runs here
Strip
Old paint or a failed coating is removed completely — chemically or by blasting — so the new finish bonds to clean metal, not to the last mistake.
Prep
Disassembly, degrease, blast to a uniform profile, degas: the steps a coating's lifespan actually depends on.
Coat and cure
Cerakote oven-cured or DuraCoat air-cured per the maker's spec, in the color or match you chose, then reassembled and function-checked.
Answers
Common questions
Someone spray-painted my gun. Can it be fixed?
Yes, and it's common. The paint comes off completely, the metal underneath is checked for rust and pitting, and the gun is refinished properly — most often in Cerakote, either a color you choose or a match to the original. A recent Glock came in rattle-canned and left in two-tone bronze.
Cerakote or DuraCoat?
Both are on the bench and both are done properly here. Cerakote is oven-cured and is the usual answer for a new color or a pattern on a modern gun. DuraCoat cures at room temperature, so it goes on parts the oven can't take and on assembled guns, and its traditional-finish line — DuraBlue, DuraPark, DuraBrown — is how an old gun gets a finish that looks like the one it was born with. A lot of restorations here are DuraCoat for that reason. Tell us the gun and what you want it to look like and we'll recommend one.
What does a refinish cost?
New-color Cerakote is priced on the Cerakote sheet by platform. Restoration refinishing is quoted from the gun because the strip and the prep vary: recent jobs ran $80 to $100 for a revolver grip frame, $100 to $120 for a pistol frame, $225 to $320 for a full handgun, and up to about $600 for a four-color stencil camo. Touch-ups are quoted on the spot.
Elsewhere on the bench
More from the shop
Gunsmithing
Handguns, rifles, shotguns and everything between — repairs, threading, triggers, optics and fitting on our own bench, quoted before we touch your firearm.
Explore →07 servicesNFA Center
Silencer sales plus Form 1 and Form 4 filing, ATF fingerprints, passport photos and gun trust notary — handled at one counter in Roswell.
Explore →03 servicesFinishing & Metalwork
Durable firearm finishes done in-house: Cerakote and stencil work, fiber-laser engraving and Form 1 marking, and parkerizing.
Explore →05 servicesLogistics & Commerce
Inbound FFL transfers, outbound firearm shipping, bulk ammunition, and FFL08 importation with Form 6 filing and CBP clearance.
Explore →Bring us the project.
Start an NFA transfer, ask about a service, or send photos for an estimate. We answer fast.