Restoration
Rust Removal & Re-Bluing
Surface rust, active pitting, a barrel that's gone brown in a closet: the rust is stopped and removed, the steel dressed, and the finish put back — re-blued or re-parkerized to match what the gun originally wore. Markings protected, pitting managed honestly, and a straight answer about what can and can't be brought back.
Stop it, remove it, then refinish
Rust is treated in that order. First the active corrosion is neutralized and stabilized so it stops spreading — on a collectible Colt Python that's sometimes the whole job, leaving the finish underneath alone. Then the surface rust is lifted with the gentlest method that works: oil and bronze wool for light freckling, chemical de-rusting or careful blasting for worse. What's left is the truth about the steel: light pitting can be dressed and polished out, deep pitting can be softened but not erased, and we'll show you which you have before anything gets refinished.
Then the finish. Most of what comes in wants bluing — a Remington 552 re-blued and cleaned, a shotgun barrel brought back to black. We don't run a hot-bluing tank, and we'll say so plainly; what we re-blue with is DuraBlue, DuraCoat's spray-on bluing, which is indistinguishable from traditional bluing to the eye and wears like DuraCoat rather than like a factory blue that rubs off at the muzzle. Pitting is filled with DuraFil before it goes on, so even badly rusted steel comes back with a clean, even surface. Cold blue is kept for small touch-ups where the rest of the finish is sound. Guns that wore parkerizing get re-parkerized: a super-rusted Remington pump, a 1911A1 brought back to "good," a Winchester 63 done as part of its restoration. Parkerizing as a finish on its own has its own page under Finishing; here it's the last step of bringing rusted steel back.
Polish and refinish, without erasing the gun
The difference between a good re-blue and a bad one is what happens before the tank. A gun polished by someone in a hurry comes out with rounded edges, dished screw holes, and roll marks that are half gone — the "buffed" look that knocks value off a Colt faster than the rust did. We polish by hand and on properly backed wheels, keep the flats flat and the edges crisp, and protect the markings. A Colt Series 80 slide polished and refinished here comes back looking like it did the day it shipped, not like a bar of soap.
How rust removal and re-bluing run here
Assess and stabilize
We stop the active rust first, then judge the steel underneath: what will polish out, what will only soften, and whether the gun should be refinished at all.
Strip and dress
Old finish and rust are removed, pitting is dressed as far as honesty allows, and the surfaces are hand-polished with the edges and markings protected.
Refinish
Re-blued in DuraBlue or re-parkerized in-house to match the original finish type and color, then oiled and reassembled.
Answers
Common questions
Can you get the pitting out?
Light pitting, yes — it polishes out and disappears under the new finish. Deep pitting is metal that's gone, and it can't be polished back; what it can be is dressed, filled with DuraFil, and finished over in DuraBlue so the surface reads clean and even. We'll show you the steel after de-rusting and tell you which you have before you commit to a refinish.
Should I re-blue a collectible?
Often not. On a gun where originality carries the value — an early Colt, a pre-war Winchester — the right job is to stop the rust, stabilize the surface, and leave the original finish alone, thin as it is. That's a treatment, not a refinish, and it's what we did on a Python that came in with rust in the flutes. We'll tell you which side of that line your gun is on.
What has this work cost recently?
Stabilizing rust on a collectible ran $100 to $120. Rust removal with cleaning and light restoration has run $45 to $270 depending on how far gone the gun was. A re-blue of a rifle and barrel ran $140 to $160; parkerizing a receiver or a whole long gun as part of a restore ran $120 to $270. Every job is quoted from the gun before we start.
Elsewhere on the bench
More from the shop
Gunsmithing
Handguns, rifles, shotguns and everything between — repairs, threading, triggers, optics and fitting on our own bench, quoted before we touch your firearm.
Explore →07 servicesNFA Center
Silencer sales plus Form 1 and Form 4 filing, ATF fingerprints, passport photos and gun trust notary — handled at one counter in Roswell.
Explore →03 servicesFinishing & Metalwork
Durable firearm finishes done in-house: Cerakote and stencil work, fiber-laser engraving and Form 1 marking, and parkerizing.
Explore →05 servicesLogistics & Commerce
Inbound FFL transfers, outbound firearm shipping, bulk ammunition, and FFL08 importation with Form 6 filing and CBP clearance.
Explore →Bring us the project.
Start an NFA transfer, ask about a service, or send photos for an estimate. We answer fast.